Get a Quote

Home / Products / DOT Push-In Fittings / DOT 90 Degree Male Elbow

DOT 90 Degree Male Elbow — DOT Push-In Fittings, product photo
DOT Push-In Fittings

DOT 90 Degree Male Elbow

Built and tested to DOT requirements (FMVSS 571.106 / SAE J844) for vehicle air brake systems, featuring easy push-to-connect assembly. These fittings are specifically designed for North American commercial vehicle applications.

Category
DOT Push-In Fittings
Material
Brass + Plastic
Tube sizes
1/8 · 5/32 · 3/16 · 1/4 · 5/16 · 3/8 · 1/2 · 5/8 · 3/4
Thread sizes
NPT / G 1/8 · 1/4 · 3/8 · 1/2
Application
Heavy-duty truck and trailer

Key Features

  • Built to DOT FMVSS 571.106 / SAE J844 requirements (DOT range)
  • High-pressure resistance
  • Corrosion-resistant materials
  • Easy installation and maintenance
  • Wide temperature operating range

About the 90 Degree Male Elbow

The 90 Degree Male Elbow — DOT Push-In Fittings is a Brass + Plastic fitting from the DOT Push-In Fittings range. An elbow fitting turns an air line through 90 degrees. It is used where a tube must leave a valve, reservoir or brake chamber and run along a chassis rail or frame member: the fitting takes the corner so the tube itself is never bent sharply or kinked. The push-in end accepts the tube, and the threaded end screws into the port.

Where it fits

In a truck or trailer air brake circuit, this 90 degree male elbow is used where a line must turn at a port — for example at a reservoir outlet, where stored air feeds a relay valve. On a North American Class 8 tractor and semi-trailer the same fitting is used on the service and emergency air lines between tractor and trailer, including the red and blue coiled lines at the gladhand connection.

Fitting the 90 Degree Male Elbow

Fitting the 90 Degree Male Elbow: To fit it, cut the nylon tube square, push it fully home into the collet until it seats, then pull it back to check it is locked. To remove it, press the release and pull the tube out. No spanner is needed on the tube side.

Sizes and standard

The 90 Degree Male Elbow — DOT Push-In Fittings belongs to the DOT Push-In Fittings range. Material: Brass + Plastic. Category tube sizes: 1/8 · 5/32 · 3/16 · 1/4 · 5/16 · 3/8 · 1/2 · 5/8 · 3/4. Category thread sizes: NPT / G 1/8 · 1/4 · 3/8 · 1/2. Built to FMVSS 571.106 / SAE J844 for North American vehicle air brake systems. The DOT push-in range in the factory catalogue is rated from vacuum to 250 psi, -40°F to +200°F, for tube outside diameters from 1/8 in to 3/4 in with NPTF threads. The range is a replacement for Parker Legris DOT push-in fittings.

Category range, not per-model data: the sizes above are the DOT Push-In Fittings range as published. The exact tube size, thread size and dimensions of the 90 Degree Male Elbow — DOT Push-In Fittings are confirmed against the factory catalogue when you inquire — send the part number, or the tube and thread you need, and we quote the exact model.

Complete the circuit

Most buyers add the matched PA12 tubing, truck cables & coiled air lines or EBS lines to the same order — one quote, one shipment.

See companion lines →
Call +86-17825829635
Keep looking

Related products